After a monitoring system enters the commissioning phase, commissioning phase, and after delivery, there may be such failure phenomena. These failure phenomena are not normal operation, or the system does not meet the technical requirements of the design requirements, or the overall performance. And the quality is not ideal. Here are some of the more common faults that are provided to netizens for reference.
1. Incorrect equipment caused by power failure
Solution: There are several possibilities for incorrect power supply: incorrect power supply line or power supply voltage, insufficient power (or insufficient line diameter of a certain power supply line, excessive voltage drop, etc.), short circuit in the transmission line of the power supply system, and open circuit , instant overpressure and so on. In particular, the device may be damaged due to power supply errors or instantaneous overvoltage.
2. Line failure
Because some lines, especially those connected to the equipment, are not handled well, causing circuit breakers, short circuits, poor insulation between the lines, miswiring, etc. cause damage to the equipment (or components), degradation of performance, or failure of the equipment itself, but The phenomenon is reflected in the equipment or components. In particular, the quality of some connectors is poor, and the connection process is not good. This is a common cause of problems.
Solution: In this case, the analysis should be conducted calmly based on the fault phenomenon to determine which of the faults occurred on several lines due to the connection of which lines. This will reduce the scope of the problem. For example, a camera with three variable lens image signal is normal, but the lens can not control, you do not have to check the video output line, but just check the lens control line on the line. In addition, connectors, especially BNC type connectors, are very high in the welding process and the connection and installation process requirements of video cables. If they are not handled properly, even if there are no problems in the commissioning and commissioning stages, problems occur after a period of operation. It is particularly worth pointing out that cameras with pan-tilt heads have a long time due to all-round movements, resulting in disconnection and breakage of connections that are common. Therefore, special attention should be paid to the connection of equipment and various lines in this case to meet the requirements of long-term operation.
3. The quality of equipment or components itself
In general, there should be no quality problems with carefully selected commercialized equipment or components.
Workaround: Even if problems occur, they often occur after the system has been delivered and run for a long time. In addition to the quality of the product mentioned above, the most common problem is due to improper adjustment of the equipment. For example, the adjustment of the intercept after the camera is a very precise and precise job. Without careful adjustment, problems such as poor focusing or defocusing in various operations of the three-variable lenses may occur. In addition, whether the positions of some switches and adjustment knobs of the camera are correct, whether they meet the technical requirements of the system, the correctness of the encoder coding switch or other adjustable position settings directly affect the normal use of the device itself or affect the normal performance of the entire system.
4. Problems caused by incorrect connection between equipment (or parts) and equipment (or parts)
Solution: The impedance does not match. If the video is connected to a monitor with a high impedance, the image will be very bright, the characters may jitter, or sometimes there may be characters. The communication interface or communication method is incorrect. This situation often occurs between the control host and a device such as a decoder or control keyboard that has a communication control relationship. This is mostly due to the fact that the selected control host and decoder or control keyboard are not products of one manufacturer. In general, different manufacturers use different communication methods or transmission control codes. Therefore, the same manufacturer's products should be used for the host, the decoder, and the control keyboard.
Drive capacity is insufficient or exceeds the prescribed number of device connections. For example, the number of main control keyboards and sub-control keys corresponding to the control host is regulated. Exceeding the prescribed amount will cause the system to work abnormally. Decoder pan/tilt working power power is lower than the actual pan-tilt, it can not drive the PTZ.
5. The failure of the head
A pan/tilt is incapable of operation or cannot rotate at a short time after use. It is a common troubleshooting method for PTZ: In addition to the product quality factors, the appearance of this kind of situation is mainly caused by the following reasons; only the camera is allowed to be The head mounted (that is, the camera sitting on the upper part of the turntable) uses a hoisting method (ie, the camera is mounted under the turntable). In this case, the hoisting method leads to an increase in the operational load of the pan/tilt. Therefore, the use of the hoisting method will soon lead to damage to the drive mechanism of the pan/tilt, or even burn the motor.
The total weight of the camera and its protective cover exceeds the weight of the PTZ. Especially for PTZs that are used outdoors, the weight of the protective cover is often too large, and there is often the problem that the PTZ will not move (especially the vertical direction). The outdoor pan/tilt head is faulty or even damaged due to poor ambient temperature, low temperature, waterproof, and frost protection measures.
6. Remote control failure
When the distance is too far, the keyboard cannot be controlled by the decoder on the camera (including the lens) and the pan-tilt. Solution: This is mainly because the control signal is greatly attenuated when the distance is too far, and the control signal received by the decoder is too weak. of. At this time, a relay box should be installed at a certain distance to amplify the shaping control signal.
7 monitor image contrast is too small, the image is light
Solution: If this phenomenon is not the problem of controlling the host computer and the monitor itself, it is the transmission distance is too far or the video transmission line attenuation is too large. In this case, the line amplification and compensation device should be added.
8. Image clarity issues
The sharpness of the image is not high, the detail is lost, and the color signal is lost or the color saturation is too small when the image is severe. Solution: This is because the loss of the high-frequency end of the image signal is so great that the signal with a frequency above 3 MHz is basically lost. In this case, either the transmission distance is too long and there is no amplification compensation device in the middle; or the distribution capacitance of the video transmission cable is too large; or the equivalent capacitance is concentrated in the transmission link between the core wire and the shielded wire. Caused.
9. Hue distortion
Solution: This is a fault phenomenon that can easily occur in long-distance video baseband transmission. The main reason is caused by the large phase shift of the high frequency band caused by the transmission line. In this case, a phase compensator should be added.
10. Operation keyboard malfunction
Solution: This phenomenon can basically be determined as the "deadlock" of the keyboard when checking the connection. The explanation of the operation of the keyboard, there are generally methods to solve the "crash", such as "whole machine reset" and other methods, this method can be used to solve. If it cannot be solved, it may be that the keyboard itself is damaged.
11. The host does not clean the image
Solution: The symptom of this kind of fault phenomenon is the interference of other pictures, or the interference of the line synchronization signal of other pictures on the screen after the selection. This is due to the poor quality of the matrix switcher of the host and the lack of isolation between images. If a radio frequency transmission system is used, it may also be caused by the system's cross-talk modulation and excessive modulation.
A large-scale television monitoring system that operates in conjunction with burglar alarms is a high-tech and complex system. Although various kinds of failure phenomena may occur, as long as the quality of selected equipment and equipment is properly shut down and construction is strictly conducted in accordance with standards and specifications, generally no major problems will arise. Even if there is a problem, as long as the analysis and thinking is calm, “doing the right thing†does not blindly make a big dismantling, it will solve the problem faster.
12. Bad communication failure
Solution: The performance of a controlled pan/tilt or motorized lens can sometimes be normal, sometimes it cannot be (or delayed), or it can't be stopped after the action. This is due to a problem with the communication line. Check the RS-485 communication terminal matching resistor (120|?) on the decoder when confirming the wiring is correct and the circuit is correct. Or disconnect the host interface and the far-end matching resistor, use a multimeter to measure the DC resistance RD of the terminal pin of the single communication chip and the DC resistance R2 of the communication port of the entire system, and compare it with the theoretical calculation (R2=R0/n, where n For the number of decoders connected in the entire system), if the difference is too large, it can be determined that there is a problem with the communication chip, and the problematic chip is found by the point-by-point elimination method. If the communication line has many branches, you can disconnect each branch to determine the approximate range of communication failures.
1. Incorrect equipment caused by power failure
Solution: There are several possibilities for incorrect power supply: incorrect power supply line or power supply voltage, insufficient power (or insufficient line diameter of a certain power supply line, excessive voltage drop, etc.), short circuit in the transmission line of the power supply system, and open circuit , instant overpressure and so on. In particular, the device may be damaged due to power supply errors or instantaneous overvoltage.
2. Line failure
Because some lines, especially those connected to the equipment, are not handled well, causing circuit breakers, short circuits, poor insulation between the lines, miswiring, etc. cause damage to the equipment (or components), degradation of performance, or failure of the equipment itself, but The phenomenon is reflected in the equipment or components. In particular, the quality of some connectors is poor, and the connection process is not good. This is a common cause of problems.
Solution: In this case, the analysis should be conducted calmly based on the fault phenomenon to determine which of the faults occurred on several lines due to the connection of which lines. This will reduce the scope of the problem. For example, a camera with three variable lens image signal is normal, but the lens can not control, you do not have to check the video output line, but just check the lens control line on the line. In addition, connectors, especially BNC type connectors, are very high in the welding process and the connection and installation process requirements of video cables. If they are not handled properly, even if there are no problems in the commissioning and commissioning stages, problems occur after a period of operation. It is particularly worth pointing out that cameras with pan-tilt heads have a long time due to all-round movements, resulting in disconnection and breakage of connections that are common. Therefore, special attention should be paid to the connection of equipment and various lines in this case to meet the requirements of long-term operation.
3. The quality of equipment or components itself
In general, there should be no quality problems with carefully selected commercialized equipment or components.
Workaround: Even if problems occur, they often occur after the system has been delivered and run for a long time. In addition to the quality of the product mentioned above, the most common problem is due to improper adjustment of the equipment. For example, the adjustment of the intercept after the camera is a very precise and precise job. Without careful adjustment, problems such as poor focusing or defocusing in various operations of the three-variable lenses may occur. In addition, whether the positions of some switches and adjustment knobs of the camera are correct, whether they meet the technical requirements of the system, the correctness of the encoder coding switch or other adjustable position settings directly affect the normal use of the device itself or affect the normal performance of the entire system.
4. Problems caused by incorrect connection between equipment (or parts) and equipment (or parts)
Solution: The impedance does not match. If the video is connected to a monitor with a high impedance, the image will be very bright, the characters may jitter, or sometimes there may be characters. The communication interface or communication method is incorrect. This situation often occurs between the control host and a device such as a decoder or control keyboard that has a communication control relationship. This is mostly due to the fact that the selected control host and decoder or control keyboard are not products of one manufacturer. In general, different manufacturers use different communication methods or transmission control codes. Therefore, the same manufacturer's products should be used for the host, the decoder, and the control keyboard.
Drive capacity is insufficient or exceeds the prescribed number of device connections. For example, the number of main control keyboards and sub-control keys corresponding to the control host is regulated. Exceeding the prescribed amount will cause the system to work abnormally. Decoder pan/tilt working power power is lower than the actual pan-tilt, it can not drive the PTZ.
5. The failure of the head
A pan/tilt is incapable of operation or cannot rotate at a short time after use. It is a common troubleshooting method for PTZ: In addition to the product quality factors, the appearance of this kind of situation is mainly caused by the following reasons; only the camera is allowed to be The head mounted (that is, the camera sitting on the upper part of the turntable) uses a hoisting method (ie, the camera is mounted under the turntable). In this case, the hoisting method leads to an increase in the operational load of the pan/tilt. Therefore, the use of the hoisting method will soon lead to damage to the drive mechanism of the pan/tilt, or even burn the motor.
The total weight of the camera and its protective cover exceeds the weight of the PTZ. Especially for PTZs that are used outdoors, the weight of the protective cover is often too large, and there is often the problem that the PTZ will not move (especially the vertical direction). The outdoor pan/tilt head is faulty or even damaged due to poor ambient temperature, low temperature, waterproof, and frost protection measures.
6. Remote control failure
When the distance is too far, the keyboard cannot be controlled by the decoder on the camera (including the lens) and the pan-tilt. Solution: This is mainly because the control signal is greatly attenuated when the distance is too far, and the control signal received by the decoder is too weak. of. At this time, a relay box should be installed at a certain distance to amplify the shaping control signal.
7 monitor image contrast is too small, the image is light
Solution: If this phenomenon is not the problem of controlling the host computer and the monitor itself, it is the transmission distance is too far or the video transmission line attenuation is too large. In this case, the line amplification and compensation device should be added.
8. Image clarity issues
The sharpness of the image is not high, the detail is lost, and the color signal is lost or the color saturation is too small when the image is severe. Solution: This is because the loss of the high-frequency end of the image signal is so great that the signal with a frequency above 3 MHz is basically lost. In this case, either the transmission distance is too long and there is no amplification compensation device in the middle; or the distribution capacitance of the video transmission cable is too large; or the equivalent capacitance is concentrated in the transmission link between the core wire and the shielded wire. Caused.
9. Hue distortion
Solution: This is a fault phenomenon that can easily occur in long-distance video baseband transmission. The main reason is caused by the large phase shift of the high frequency band caused by the transmission line. In this case, a phase compensator should be added.
10. Operation keyboard malfunction
Solution: This phenomenon can basically be determined as the "deadlock" of the keyboard when checking the connection. The explanation of the operation of the keyboard, there are generally methods to solve the "crash", such as "whole machine reset" and other methods, this method can be used to solve. If it cannot be solved, it may be that the keyboard itself is damaged.
11. The host does not clean the image
Solution: The symptom of this kind of fault phenomenon is the interference of other pictures, or the interference of the line synchronization signal of other pictures on the screen after the selection. This is due to the poor quality of the matrix switcher of the host and the lack of isolation between images. If a radio frequency transmission system is used, it may also be caused by the system's cross-talk modulation and excessive modulation.
A large-scale television monitoring system that operates in conjunction with burglar alarms is a high-tech and complex system. Although various kinds of failure phenomena may occur, as long as the quality of selected equipment and equipment is properly shut down and construction is strictly conducted in accordance with standards and specifications, generally no major problems will arise. Even if there is a problem, as long as the analysis and thinking is calm, “doing the right thing†does not blindly make a big dismantling, it will solve the problem faster.
12. Bad communication failure
Solution: The performance of a controlled pan/tilt or motorized lens can sometimes be normal, sometimes it cannot be (or delayed), or it can't be stopped after the action. This is due to a problem with the communication line. Check the RS-485 communication terminal matching resistor (120|?) on the decoder when confirming the wiring is correct and the circuit is correct. Or disconnect the host interface and the far-end matching resistor, use a multimeter to measure the DC resistance RD of the terminal pin of the single communication chip and the DC resistance R2 of the communication port of the entire system, and compare it with the theoretical calculation (R2=R0/n, where n For the number of decoders connected in the entire system), if the difference is too large, it can be determined that there is a problem with the communication chip, and the problematic chip is found by the point-by-point elimination method. If the communication line has many branches, you can disconnect each branch to determine the approximate range of communication failures.
Zhejiang Sealand Technology Co., Ltd. is a trustworthy manufacturer of Natural Gas Mass Flow Meter, Natural Gas Mass Flowmeter, Natural Gas Coriolis Meter, Natural Gas Coriolis Mass Flow Meter, ATEX, IECEx & CE approved.
First, Sealand meter is certified by Zhejiang Institute of Metrology. To get such certificate, Sealand has to send all models to Zhejiang Institute of Metrology and all models are tested in their calibration lab. The lab is an ISO/IEC 17025:2005 standard lab approved by CNAS (China National Accreditation Service for Conformity Assessment). CNAS is a member of ILAC (International Laboratory Accreditation Cooperation).
Second, Sealand has its own calibration lab, equipped with METTLER TOLEDO scales with accuracy 0.014% and the device extended uncertainty is 0.05%. The lab is also approved by Zhejiang Institute of Metrology. This certificate will stay valid only for one year, Zhejiang Institute of Metrology will send their professor to Sealand every year to check and make sure that the lab is qualified still and then issue new certificate. During the production, each meter will be calibrated in this lab for 3 times, each time at 5 different flow rate.
Finally, Sealand also gets ISO, CE, SIL, ATEX & IECEx. Sealand is the only Chinese brand who gets ATEX & IECEx and it is from TUV SUD ( the most authoritative institute for ATEX).
Natural Gas Mass Flow Meter, Natural Gas Mass Flowmeter, Natural Gas Coriolis Meter, Natural Gas Coriolis Mass Flow Meter
Zhejiang Sealand Technology Co., Ltd. , https://www.sealandflowmeter.com