There is a washing machine in every household. The washing machine is a good helper for our daily cleaning of clothes. It brings us a lot of convenience. With the progress of the society, there has been a fully automatic washing machine, which can completely liberate our hands. It only needs to be washed and dried. But to buy a new automatic washing machine, we need to install it ourselves, then how to connect the faucet with the automatic washing machine ? Let's take a look at the installation method and precautions of the automatic washing machine together with the decoration home network.
How to connect the faucet to the automatic washing machine?
The automatic washing machine has a high-pressure water pipe, one end is connected to the water inlet of the washing machine, and one is placed on the faucet of the flat mouth. There is a white plastic screw to loosen. After tightening the four screws on the top, tighten the white plastic screw clockwise. In the socket test, if the water is leaking, there is a leak in the flat surface and check whether there is a gap in the flat outlet of the faucet. After the completion, re-install according to the above procedure, the white plastic screw is loosened and the four screws are tightened. Plastic screws.
Automatic washing machine installation method
Take out the automatic washing machine inlet pipe fitting, find the end with the inlet pipe joint, and then press the slider to separate the inlet pipe joint from the inlet pipe, as shown in the figure: loosen the four screws on the inlet pipe joint evenly To the faucet can be inserted, if the faucet is too large, you can go to the lower bushing. Then loosen the plastic interface nut to expose approximately 3-4 turns of thread.
Put the inlet pipe joint on the faucet, attach the black washer in the joint to the faucet, and then tighten the screw with a screwdriver, as shown in the figure: tighten the plastic interface nut, tighten until it leaks, and then connect the inlet pipe. Connect with the water inlet pipe as shown in the figure: connect the other end of the water inlet pipe to the water inlet of the fully automatic washing machine, tighten the plastic nut, and install it.
Automatic washing machine installation skills:
1, location placement
The fully automatic washing machine should be placed on a flat, stable floor. When the inclination of the ground is extremely small, the foot of the washing machine can be adjusted.
2, the setting of the drain
The drain pipe should use the special pipe for the washing machine. There should be air flow between the drain pipe and the sewer. It should not be blocked or bent.
3, the installation of the inlet pipe
If the inlet pipe of the fully automatic washing machine is installed incorrectly, it will easily cause the inlet pipe to leak. Proper installation is a basic skill of the washing machine repairman.
Automatic washing machine installation precautions:
1, the correct placement of the washing machine
1) Avoid placing it in a damp place to prevent long-term moisture and rust or wire connector short circuit.
2) Avoid placing it in direct sunlight or in places with high temperature. Avoid heat sources as much as possible to prevent deformation of plastic parts and discoloration of paint.
2, power socket and ground wire installation
1) When installing the power socket of the washing machine, be sure to check the rated voltage and rated frequency on the nameplate of the washing machine. China's power grid voltage is 220v and the frequency is 50Hz.
2) The power socket should not be more than 2.0m away from the working position of the washing machine. If the fuse is not installed in the washing machine, install a 5A fuse on the power strip to prevent the meter from being burnt out if a short circuit occurs.
The above content is the introduction of the automatic washing machine installation method and precautions brought by everyone in this small series for your reference. I believe that after reading this article, we will have a certain understanding of how to fully automatic washing machine. You can give some help to friends who are installing fully automatic washing machines. For more exciting home improvement content, please continue to pay attention to the decoration home network.
More related wonderful reading:
Automatic washing machine purchase method, automatic washing machine is good?
What is the reason why the automatic washing machine does not enter the water? How to deal with it?
How to use automatic washing machine? Introduction of automatic washing machine
Cold Drawn Steel Round Bar is produced by cold drawing from hot rolled Steel Round Bar or hot rolled steel wire rod. Our advantages and more services of cold drawn steel Round Bar includes:
1) Wide range of diameters from 10mm to 150mm
2) Customized Length from 100mm to 12000mm
3) Good surface roughness: 0.4um to 1.6um
4) Good straightness: 0.5mm/m to 2mm/m
5) Good roundness: 80% of diameter tolerance
6) Diameter tolerance: -0.02mm to -0.1mm / h9, h10, h11
7) Matched further processing: Grinding, polishing, straightening
8) Anti-rusty package
9) Full sets of testing equipment: Surface, Dimenstion. Mechanical properties testing
10) Fast delivery time
Cold Drawn Steel Round Bar
Steel Round Bar,Cold Drawn Round Bar,Cold Drawn Bright Bar,Cold Drawn Steel Round Bar
SHANDONG LE REN SPECIAL STEEL CO., LTD. , https://www.lerenspecialsteel.com