Wood flooring can cause tarnishing due to long-term pedaling. The advantage of floor waxing is that it can protect the surface of stone floor or wooden floor from being naturally weathered. After waxing the floor, it can effectively increase the gloss of the floor. And the appearance, the future cleaning will be more convenient. Then let Xiaobian take everyone to look at the relevant content of the related content of the wood floor repair waxing .
First, how to wax the wooden floor?
The tools and materials that need to be prepared before waxing your own wooden floor are:
Wood floor waxing tools: steel wool, sponge, rag, vacuum cleaner, waxing machine is not necessary to wax the home wood floor.
Wood floor waxing material: floor wax (children's shoes without floor wax at home, you can also consider using the leftover candle head to remove the candle heart and add the same amount of turpentine. The water is boiled and melted to form a shoe polish. It can be used as a local wax.)
Note: The waxing time is once every 1 month or 2 months. The dosage can be added in sequence. The first waxing is slightly more. For every 30 square meters of empty floor, you can play about 300 grams of floor wax.
Second, the wood floor repair waxing method
1. Remove rubbish and dirt from the floor surface. Use a vacuum cleaner to remove dirt and dust from the floor surface. Wipe the stains on the floor with a diluted neutral detergent. Wipes that are difficult to remove can be wiped with water.
2, fully dry. The moisture on the floor surface and the groove portion is completely dried to be waxed at the rear. Depending on the season, the time required varies, but it takes about half a day.
3. Cover the wall skirting line and furniture with tape paper. The purpose is to prevent the floor wax from polluting the wall skirting and furniture.
4. Shake the container with the floor wax and mix well.
5, according to the direction of the wood grain of the floor, do not leak or thick and uneven. If the amount of application is too small, unevenness will result, and too much application will result in poor film formation. Keeping it thin and even is the key to waxing.
Third, the wood floor repair waxing notes
1. To prevent the detergent from accumulating in the groove, the rag soaked with detergent should be wrung out as much as possible. Floor wax removers can cause stains and bulging on the floor and must never be used. Wipe with a wrung rag. Wipe with a rag that has been wrung out. The surface of the floor, especially the grooved part, should be carefully wiped and no detergent remains. If the detergent and moisture are left behind, it will cause whitening and swelling.
2. Everything should be carefully dried: if it is not fully dried, the floor wax will not adhere to the surface of the floor, affecting the appearance and whitening.
3, at least three times the wax, each time with a lint-free cloth or waxer to rub the floor to make the wax oil into the wood.
4, in order to get the consequences of shining, every time you hit the wax, you should use a soft cloth to lightly polish.
5, each time, after drying, use a very fine sandpaper to polish the appearance, wipe clean, and then play the second time.
How about, I read the above introduction to the waxing of the wooden floor, and I have learned a lot about the repair and waxing of the wooden floor. I hope that you can learn more about home improvement knowledge through this article, and you will be able to create a more perfect home environment. Thank you for reading this article and your support and love for Xiaobian. If you want to get more information about home improvement, please continue to pay attention to the decoration home network.
The Cable laying machines over two pairs of propelled pulleys. Two counter pulleys press the cable into the grooves of the two driving pulleys. The cable pusher tapered pulleys consist of a special high elastic and wear resistant rubber material, thus Cable Laying Equipment ensuring adequate friction.
The hydraulic power Cable Blowing Machine pack is connected with the pusher BKS 400 by two hydraulic hoses; the operation cable pusher can be easy managed from the ground, also if the pusher is fixed in a tray.
The hydraulic drive Cable Laying Equipment of the BKS 400 can be operated by a separate power pack or by another machine like an excavator, if the below listed parameters can be provided. The connecting hoses between the BKS 400 and the power pack are equipped with a flow divider, which guarantees the infinitely variable adjusting of speed.
Cable Conveyor Crawler,Power Cable Conveyor,Conveyor Cable,Cable Tube Conveyor
NINGBO MARSHINE POWER TECHNOLOGY CO., LTD. , https://www.marshine-power.com