Fault diagnosis and disposal in bearing operations

Home>Bearing knowledge> Fault diagnosis and disposal in bearing operation
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131";

Fault diagnosis and disposal in bearing operations

Source: China Bearing Network Time: 2014-11-02

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
First, the bearing's tumbling sound is selected by the sounder to check the size and sound quality of the bearing's tumbling sound; even if the bearing has slight peeling and other damage, it will announce abnormal sounds and irregular sounds; .
Second, the bearing oscillation bearing oscillation is very sensitive to bearing damage; for example, shedding, indentation, rust, crack, wear, etc. will be reflected in the bearing oscillation measurement; therefore; after the selection of special bearing oscillation measuring device (frequency analyzer, etc. The large amount of oscillation can be measured. ü De Shi Zhi 豢 豢 鲆 鲆 鲆 5 5 5 5 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭 咛迩榭. The measured value is analyzed and compared to determine the discriminant specification.
Third, the temperature of the bearing temperature of the bearing; usually the temperature outside the bearing can be estimated; if the oil hole can directly measure the bearing outer ring temperature; then more suitable. Usually; the temperature of the bearing gradually rises with the beginning of the operation; After 1-2 hours, the stability is reached. The normal temperature of the bearing is due to the heat capacity of the machine; the heat dissipation; the speed and load are different. If it is smooth and the device is suitable, the bearing temperature will rise sharply; abnormal temperature will occur; It is necessary to suspend operations; adopt necessary precautions. Based on many test data; Table 4-1 lists the average value of outer ring temperature during bearing operation in various machines; for reference. Because temperature is affected by smoothness, speed, load, environment The impact of the table; the value of the table only indicates the approximate temperature scale. The thermal sensor can be used to monitor the operating temperature of the bearing at any time; and when the temperature exceeds the rule value, the alarm is activated or the ignition is avoided.
4. Smooth. ㄒ唬┲岢腥蠡淖饔 Smooth has an important influence on the fatigue life of the rolling bearing and conflict, wear, temperature rise, oscillation, etc.; there is no normal smoothness; the bearing can not work. The reason for analyzing the bearing damage is marked 40% of bearing damage is related to poor smoothness. Therefore, the outstanding smoothness of the bearing is a useful way to reduce bearing conflict and wear. In addition to this; the smoothness of the bearing and heat dissipation; rust, sealing, flat cushioning, etc. A variety of effects; the smooth bearing effect can be briefly stated as follows:
a. An oil film is formed between the two tumbling surfaces or the sliding outer surface that touch each other to separate the two outer surfaces; the collision and wear of the touch surface are reduced.
b. When the oil is smooth, especially when the circulating oil is smooth, the oil mist is smooth and the fuel injection is smooth; the smooth oil can take away most of the conflict heat inside the bearing; it has a useful heat dissipation effect.
c. When the grease is smooth, it can avoid foreign matter such as dust from entering the bearing;
d. Smoothing agents have the effect of avoiding metal corrosion.
e. The fatigue life of the extended bearing.
The smooth method of the Vedas's leg 蠡 冉 bearing is roughly divided into two types: grease smoothness and oil smoothness. In order to give full play to the function of the bearing; it is important to use the reduction and application intentions;
ㄈ┲蠡 Smooth grease is a smoothing agent composed of base oil; thickener and additives. When selecting; should choose the grease that is very suitable for the bearing application conditions; because the trademark is not the same; there will be very functional Large difference; so in the time of selection; it is necessary to pay attention to. The smooth grease commonly used in bearings is calcium-based smooth fat, sodium-based smooth fat, calcium-sodium smooth grease, lithium-based smooth fat, aluminum-based smooth fat and molybdenum disulfide Smooth grease, etc. The amount of smooth grease filled in the bearing; suitable for 1/2-1/3 of the inner space of the overflow bearing. It should be reduced to 1/3 at high speed. Excessive smooth grease makes the temperature rise.
It’s hard to find
When selecting smooth grease according to operating temperature; the primary target should be dropping point; oxidation stability and low temperature function; dropping point can usually be used to evaluate high temperature function; bearing practice temperature should be lower than dropping point 10-20 °C. The temperature should be lower than the dropping point of 20-30 ° C. When selecting smooth grease according to the bearing load; for heavy load, the smooth grease with small penetration should be selected. When working under high pressure, the penetration is small; Oil film strength and extreme pressure function. When selecting smooth grease according to environmental conditions; calcium-based smooth fat is not easily soluble in water; suitable for dry and less watery environment.
The leg squats under high speed and high temperature conditions; when the grease is smooth, it can be used with smooth oil. After smooth oil circulation; can take away a lot of heat.
Viscosity is an important characteristic of smooth oil; the viscosity of the powder directly affects the fluidity of the smooth oil and the thickness of the oil film formed between the conflicting surfaces; the viscosity of the smooth oil at the bearing operating temperature is usually 12-15 cst. The higher the rotational speed, the lower the viscosity should be selected; The heavier should choose a higher viscosity. The commonly used smooth oils are mechanical oil, high speed mechanical oil, turbine oil, compacting oil, transformer oil, cylinder oil, etc.
The oil smoothing method includes:
a. Oil bath smooth oil bath smooth is the most common smooth method; suitable for the smoothness of low and medium speed bearings; part of the bearing is immersed in the groove; smooth oil is brought up by the rotating bearing parts; then it flows back to the oil groove. Below the middle of the lowest roll.
b. Drip oil smooth drip smooth is suitable for the quantitative supply of smooth oil bearing parts; the amount of oil is usually one drop every 3-8 seconds; too much oil will lead to increased bearing temperature.
c. The circulating oil is smooth and the oil is pumped to the bearing parts; the smooth oil after the bearing is filtered and cooled, and then used. Because the circulating oil can take away a certain amount of heat; the bearing is cooled; therefore, the method is suitable for bearings with higher speed. component.
d. The spray is smooth and mixed with smooth oil by a sprayer to form an oil mist; in the eruption bearing; the air flow can effectively cool the bearing and avoid the intrusion of impurities. This method is suitable for the smoothing of high-speed, high-temperature bearing components.
e. The illuminating and sliding oil pump pumps the high-pressure oil into the bearing through the nozzle; the oil injected into the bearing flows into the oil groove through the other end of the bearing. When the bearing rotates at a high speed; the rolling body and the cage also make the ambient air flow at a suitably high rotation speed. It is difficult to send the smooth oil to the bearing in a generally smooth manner; it is necessary to spray the smooth oil into the bearing by means of a high-pressure eruption; the nozzle should be placed between the inner ring and the middle of the cage.
┕ 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡 蠡High vacuum, corrosion resistance, radiation resistance; and special conditions such as extremely low temperature; solid smoothing agent to participate in engineering plastics or powder metallurgy materials; can be made into bearing parts with self-smooth function; such as solid lubricant with adhesive Bonded to the raceway, cage and roll body; constitutes a smooth film; has a certain effect on reducing conflict and wear.
. ㄆ撸┤蠡 牟 牟 溆敫 。 a. The smooth grease compensates for the interval because of the mechanical effect; the addition of aging and pollution; the smooth base filled in the bearing equipment will gradually lose its smooth function. Therefore, the smooth rank needs to be continuously compensated and updated. The composition, scale and speed of the bearing are different; the approximate interval of the smooth grease is compensated according to the operation time requirement; otherwise; when the bearing temperature exceeds 70 °C; the bearing temperature rises by 15 °C; Make up half of the interval. The double-sided closed bearing is now loaded with grease; "HRB" uses standard smooth grease in these products; the total operating temperature scale and other functions are suitable for the regular occasion; The amount also corresponds to the size of the bearing; the life of the grease can usually exceed the bearing life; except for special occasions; no need to make up for smooth grease.
b. Replacement cycle of smooth oil The replacement cycle of smooth oil is different depending on the application conditions and oil quantity; usually; when the working temperature is below 50 °C; when it is used in an excellent environment with less dust; replace once a year; when the oil temperature reaches At 100 ° C; replace it once every 3 months or less.
Recommend to friends comments close window

Bearing related knowledge
Analysis of the selection and application of bearings: Reasonable selection of bearings for machine tool spindles and turrets Application of oil mist system in high-function bearings Since the "new application tips" of smooth bearings
Interpretation of RHP BSB150 SUH P3 bearing type


This article links to http://
Please indicate the bearing network http://

Previous:TIMKEN® Roll Neck Bearing (2): Installation Next: Analysis of the Primary Damage Mode of Imported Bearings

1. Product introduction

   Coal-based columnar net gas Activated Carbon is cylindrical, tasteless non-toxic; as high quality anthracite the raw material, by process of crushing, mixing, extrusion, molding, drying, carbonization, activation and made. It has reasonable pore structure, good adsorption properties, high mechanical strength, able to withstand the high temperature, high pressure and not easily broken, easy to regenerate, and low cost characteristics. It is widely used in sewage treatment, gas treatment, solvent recovery, desulfurization and denitrification, nitrogen making machine, air separation equipment, paint shop and other fields.


2. Application

a.Coal columnar net gas activated carbon used for purification, such as chemical raw materials, pharmaceutical chemical synthesis gas, industrial gas, nitrogen, chlorine, hydrogen chloride, ethylene hydrocarbons, ozone, ethane, butane, cracking gas, carbon dioxide and hydrogen used in beverage; atomic facilities exhaust inert gas and remove the pollutants; also separate and purify mixed gas. It also can be used for gas masks and protective equipment disinfection and filtration.

b.Coal columnar net gas activated carbon is mainly suitable for industrial waste treatment, such as waste gas power plant, chemical plant gas, coking plant, smelting plant, oil plant. Coal columnar net gas activated carbon rely on the good adsorption capacity, developed gap, high iodine value can make a cleaning purpose.

3. Adsorption purification principle and process

  The physical properties of coal-based activated carbon introduction: it is cylindrical black particles; the physical, chemical properties analysis of carbon is a porous carbon, the highly developed pore structure makes it has large surface area, so it is easy to full contact with toxic and harmful gases in the air (and harmful impurities), so this highly developed capillary and pore structure formed a powerful adsorption force field, which gives the unique adsorption properties of activated carbon.  

Adsorption: the organic waste gas passes through the filter removed the solid particulate material, from the upper to the lower into the adsorption tank. The organic matter is captured, absorbed and concentrated by the activated carbon, and the purified air is discharged from the lower part of the tank through the main fan into the atmosphere.

    Stop: when activated carbon adsorption reached saturation,it stops to inhalation waste gas; and then blowing up into the steam through the activated carbon bed, which expelled the organic matter from the activated carbon, and the subsequent restoration of desorption, activated carbon activity is recycled.

    Hot air drying and cooling: the activated carbon layer after desorption remains 80%-90% steam condensate which can in reducing carbon layer activity; therefore using the hot air to dry, close the steam valve, and then through the air cooling at 25 DEG C, activated carbon can be recovered into the circulation.

     


Columnar Net Gas Activated Carbon

Columnar Net Gas Activated Carbon,Columnar Activated Carbon,Pellet Activated Carbon For Gas Mask

Ningxia XingKai Silicon Industry Co., Ltd. , https://www.xingkaisic.com